Feet-Inch Fraction Calculator

Add and subtract measurements the way they read on a tape measure: 12' 6 3/8", 6-3/8 or 3.2m. See the answer in feet, inches and fractions, decimals and metric.

Round to

The red line is where your answer lands on the tape. The orange band is the rounding zone for the precision you pick.

1. Type or tap a measurement

Join measurements with + − × ÷. Put spaces around a minus sign. A plain number is read as inches.

Result

0"

All units feet, decimals, metric
    Tape history empty
    • Press = to add a line to the tape.

    Diagonal (check for square)

    Corner-to-corner distance of a rectangle. Both diagonals of a square layout should match this.

    Equal spacing (balusters, pickets)

    Even gaps between posts with a set number of balusters.

    How this feet-inch calculator works

    Everything is converted to inches, calculated in decimal, then converted back. That avoids the mistakes people make carrying fractions by hand. The ft-in answer is rounded to the nearest 1/2, 1/4, 1/8, 1/16 or 1/32 inch (your choice); the decimal and metric lines are not rounded. A measurement with no unit is treated as inches, and 25.4 mm equals one inch exactly.

    You typeRead as
    12' 6 3/8"12 feet, 6 and 3/8 inches
    12'-6 3/8"same, with a dash after the feet
    6-3/8 or 6 3/8"6 and 3/8 inches
    150.5"150.5 inches = 12' 6 1/2"
    12.5'12.5 feet = 12' 6"
    3.2m, 3200mm, 320cmmetric; 3.2 m is about 10' 6" (125.984 in)
    10' - 3 1/2"subtract (spaces around the minus)
    8' 4" ÷ 5divide by a plain number
    Diagonal tool

    The diagonal is the Pythagorean theorem: the square root of width squared plus length squared. To square a foundation, deck or wall layout, measure corner to corner both ways. If the two diagonals match, the corners are square. The 3-4-5 triangle is the same math with whole numbers.

    Equal spacing tool

    With n balusters of width w between two posts a distance L apart, there are n + 1 equal gaps. Each gap is (L − n × w) ÷ (n + 1), and the center-to-center spacing is that gap plus w. The model residential code (IRC R312.1.3) says guard openings must not allow a 4-inch sphere to pass, so we flag any gap of 4 inches or more. Your local code and the plans for your project come first, and stair guards have additional opening rules.

    Sources

    A planning aid, not a substitute for measuring twice. Check critical dimensions on site.

    Estimates only — not engineering, legal or code advice. Check requirements with your local building department and a licensed professional before you build.

    Common questions

    How do I add feet and inches with fractions?

    Type each measurement and join them with +. For example 12' 6 3/8" + 3' 4 1/2" gives 15' 10 7/8". The calculator adds the fractions, carries 12 inches into a foot for you and shows the answer rounded to the precision you pick (1/2 to 1/32 inch).

    What formats can I type?

    Feet and inches (12' 6 3/8" or 12'-6 3/8"), inches only (6-3/8, 6 3/8" or 150.5"), decimal feet (12.5'), and metric (3.2m, 3200mm, 320cm). A number with no unit is read as inches, the way a tape measure works. Put spaces around the minus sign when subtracting, such as 10' - 3 1/2", so it is not mistaken for the dash in 6-3/8.

    How do I multiply or divide a measurement?

    Use x or × to multiply and ÷ to divide by a plain number. For example 8' 4" ÷ 5 = 1' 8" and 2' 3 1/4" x 4 = 9' 1". Dividing one length by another gives a plain ratio.

    What does the precision setting do?

    It sets the smallest fraction the ft-in answer is rounded to: 1/2, 1/4, 1/8, 1/16 or 1/32 inch. The decimal and metric lines are not rounded. For example 3.2 m is 125.984 in, which reads as 10' 6" at 1/16 inch.

    How do I check that a layout is square?

    Measure both diagonals of the rectangle. If they are equal, the corners are square. Use the diagonal tool for the number you should see: a 12' x 16' rectangle should measure 20' 0" corner to corner. The 3-4-5 rule is the same idea, since 3' and 4' sides give a 5' diagonal.

    How many balusters do I need on a railing?

    Guards generally must not let a 4-inch sphere pass through (IRC R312.1.3), so the clear gap between balusters must be under 4 inches. For an 8' (96 in) run with 1 1/2 in square balusters you need at least 17, which leaves gaps of about 3 15/16 in. With 16 the gaps would be 4 1/4 in. Always confirm the rule with your local building department.